Identification and genotoxicity evaluation of potential impurities in rabeprazole sodium using in silico and in vitro analyses.

Rabeprazole sodium is a widely used drug for gastrointestinal disorders. Several analytical methods for identifying rabeprazole sodium and its impurities have been reported. However, the genotoxicity of rabeprazole sodium and its impurities is still unclear. Thus, it is necessary to develop analytical methods that can identify the structures of its impurities and evaluate their genotoxicity. Here, we used high-performance liquid chromatography-quadrupole time-of-flight mass spectrometry for identifying the impurities in rabeprazole sodium enteric-coated tablets. Impurities in the samples were matched with synthesized impurities based on the exact mass and secondary mass spectrometry characteristics and then subjected to in silico analysis using the Derek and Sarah software, as well as in vitro genotoxicity evaluations. Our method successfully identified the impurities as 2-[[4-(3-methoxy propane)-3-methyl-N-oxido-2-pyridyl] methyl sulfonyl]-1H-benzimidazole (impurity I), 2-[[4-(3-methoxy propane)-3-methyl-2-pyridyl]methyl sulfonyl]-benzimidazole (impurity II), 2-[[4-(3-methoxy propane)-3-methyl-2-pyridyl] methionyl]-1H-benzimidazole (impurity III), and 2-mercapto benzimidazole (impurity IV). In silico analysis predicted that impurity III demonstrated a structural alert; thus, this impurity was evaluated for in vitro genotoxicity using the Ames test and chromosomal aberration assay. Impurity III at concentrations of 7.5-30 µg/mL had an aberration rate of over 5% with or without S-9 mix. Furthermore, impurity III at concentrations of 40-1000 µg/plate significantly increased the number of mutagenic colonies with or without S-9 mix. These results indicated that impurity III should be regulated to the limit of 0.01%.

A simple, sensitive, and straightforward LC-MS approach for rapid analysis of three potential genotoxic impurities in rabeprazole formulations.

In the present study, a sensitive and fully validated liquid chromatography with mass spectrometry method was developed for the quantification of three potential genotoxic impurities in rabeprazole drug substance. The separation was achieved on Symmetry C18 column (100 × 4.6 mm, 3.5 µm) using 0.1% formic acid in water as mobile phase A and acetonitrile as mobile phase B in gradient elution mode at 0.5 mL/min flow rate. Triple quadrupole mass detection with electrospray ionization was operated in selected ion recording mode for the quantification of impurities. The calibration curves were demonstrated good linearity over the concentration range of 1.0-4.5 ppm for O-phenylenediamine, 1.8-4.5 ppm for 4-nitrolutidine-N-oxide and 1.0-4.5 ppm for benzyltriethylammonium chloride with respect to 10 mg/mL of rabeprazole. The correlation coefficient obtained in each case was >0.998. The recoveries were found satisfactory over the range between 94.22 and 106.84% for all selected impurities. The method validation was carried out following International Conference on Harmonization guidelines, from which the developed method was able to quantitate the impurities at 1.0 ppm for O-phenylenediamine, 1.8 ppm for 4-nitrolutidine-N-oxide and 1.0 ppm for benzyltriethylammonium chloride. Furthermore, the proposed method was successfully evaluated for the determination of selected impurities from bulk drug and formulation samples of rabeprazole within the acceptable limits.

Analysis of potential genotoxic impurities in rabeprazole active pharmaceutical ingredient via Liquid Chromatography-tandem Mass Spectrometry, following quality-by-design principles for method development.

A novel Liquid Chromatography-tandem mass spectrometry (LC-MS/MS) method is presented for the quantitative determination of two potential genotoxic impurities (PGIs) in rabeprazole active pharmaceutical ingredient (API). In order to overcome the analytical challenges in the trace analysis of PGIs, a development procedure supported by Quality-by-Design (QbD) principles was evaluated. The efficient separation between rabeprazole and the two PGIs in the shortest analysis time was set as the defined analytical target profile (ATP) and to this purpose utilization of a switching valve allowed the flow to be sent to waste when rabeprazole was eluted. The selected critical quality attributes (CQAs) were the separation criterion s between the critical peak pair and the capacity factor k of the last eluted compound. The effect of the following critical process parameters (CPPs) on the CQAs was studied: %ACN content, the pH and the concentration of the buffer salt in the mobile phase, as well as the stationary phase of the analytical column. D-Optimal design was implemented to set the plan of experiments with UV detector. In order to define the design space, Monte Carlo simulations with 5000 iterations were performed. Acceptance criteria were met for C8 column (50×4mm, 5µm), and the region having probability π≥95% to achieve satisfactory values of all defined CQAs was computed. The working point was selected with the mobile phase consisting of ACN, ammonium formate 11mM at a ratio 31/69v/v with pH=6,8 for the water phase. The LC protocol was transferred to LC-MS/MS and validated according to ICH guidelines.